Reasons Your fiat 500 key cover 500 fiat abarth key Fob Won't Work

A fiat 124 spider key fob cover 500 key fob allows you to easily open doors and start your car. However, there are many reasons why the key fob might stop functioning. This includes a dead battery or water damage, problems with the receiver modules, and interference.

This listing is for an NEW replacement fiat punto car key Flip Key Remote - an exact replica of the Ilco brand that needs to be programmed professionally by a local locksmith (click here for Locksmith Search). Includes lock, unlock, and trunk buttons.

Dead Coin Battery

A dead battery is the main reason for your 500 key fob not working. Modern key fobs have a very restricted operating range, and must be within some feet of the vehicle how to get a replacement key for fiat 500 operate. If you are not within your vehicle and you push the keyfob button it won't respond and display the message "Key Fob Not Detected".

If this happens, replace the battery in the coin cell (Part number CR2032) by a new one from a reputable brand like Panasonic, Duracell, or Energizer. They are usually available at your local hardware store or on the internet.

After you've replaced the battery in the coin cell, you can test it by standing next to your fiat Doblo Key Fob programming 500 and pressing the buttons. The parking lights should flash and the key fob will operate the lock and unlock switches.

If your key fob still does not work after replacing the battery, it may be water damage that prevents it from connecting to the module inside your vehicle. Water damage can happen in many ways, such as an easy splash or submerging the key fob in saltwater at the beach. If you suspect that your fob was exposed to water, put it in a rice bag to draw out the moisture. If this fails, you'll need to have your fob reset by an auto locksmith or a dealer.

Water Damage

Although the fob is equipped with rubber seals that keep water from the chip's electronic circuit the device, submerging it into the ocean or washing it in a machine could cause water damage. Saltwater poses a particular risk to the fob's circuit board which causes it to short out and eventually end up dying. In the event that you let your fob get wet, it's not a good idea but if you drop it in a cup of water or forget to remove it from your pants pocket before running the washing machine Don't give up hope.

Remove the battery first. Before replacing the battery clean the electronic chip with isopropyl, or a similar product. Then test the fob to verify if it is working. If the key still doesn't work, it may have to be reprogrammed. This is typically handled by a dealer or professional auto locksmith.

If the key you have is older and is not programmed for your vehicle You will need to replace it completely. This is a simple process which can be accomplished by a professional locksmith for automotive use. The locksmith must cut the key to match the ignition on your vehicle. The locksmith will also have to reprogram your fob in the car's system. This is a cheap and quick procedure that can be completed in the same day.

Receiver Module Issues

One of the simplest reasons your 500 key fob may stop functioning is because it's out of range. The remote has a range of 30 feet. So if you are too far away from your vehicle, it won't respond to your commands. It is possible to solve this issue by moving the remote closer to your car until it responds.

If you've replaced the battery in your coin (commonly known as"button" or "button" or "watch") and your fob doesn't function, it could have an internal circuit board problem. In most cases, reprogramming the fob will fix the problem. The instructions are available for most vehicles on YouTube or in the owner's manual.

It may be necessary to replace the metal clips that hold the coin batteries in the correct position. If they loose tension, it could hinder the coin battery from being seated properly and could cause the remote to malfunction.

In rare cases the fob could be disconnected from your vehicle because of software or hardware issues. You can fix this problem by visiting your local auto-locksmith or dealer to reprogram your key fob. In some instances the software might require reinstallation into your body control modules.

Interference

In addition to a dead coin battery, the key fob may not be receiving or transmitting an signal due to interference. This could happen if the key fob is near the radio transmitter (cell phones, radar detectors) or any other source of electromagnetic radiation. Other reasons the key fob might not function include a poor connection to the buttons, damage to the internal chip or water damage.

If your key fob suddenly stopped working, or if you have tried everything at home to solve the issue (e.g. You could have a malfunctioning 500 receiver module after you've tried replacing the battery, reprogramming or using an alternative key fob. The receiver module, which is located beneath the dashboard, is able to pick up radio frequency signals from your key fob. It converts them into electronic commands that the vehicle interprets.

There's a quick and easy way to reset the 500's internal system, including the keyfob. Disconnect the battery for 15 minutes by removing first the negative cable, then the positive cable. Reconnect the battery. This will get rid of any residual electricity and restart the car's computers, which can help you get your key fob working again. If the problem persists you should speak with an expert technician. They will be able to diagnose the exact cause of your issues.