how to get a replacement key for a kia sorento to Replace a Kia Sportage Replacement Key

For a number of Kia models keys, the key has a built-in keyless entry system. The key is usually akin to an electronic remote and can be changed with a fresh one from an Kia dealer or a locksmith.

Key fobs may stop working due to a variety of reasons, including the battery being dead, worn-out buttons, signal interference or water damage. Here are some suggestions on how you can get your Kia Sportage replacement key working again.

How to replace the remote key or the smart key?

The battery inside your Kia's smart key will eventually need to be replaced, whether it's a remote that starts with a push button or a standard metal key that doesn't contain a transponder. This is particularly true if the car displays a message telling that the remote or smart key has low battery power.

Fortunately, it's an easy procedure. To replace the battery in the keyfob remove your mechanical key from the slit on the back of the fob. Then, pry the cover off. Inside the key fob there will be an incredibly small screw that holds the battery in the correct position. By using a small screwdriver loosen the screw and pull out the old battery. Then, insert the new and close the slit in the key fob.

Test the key fob by pressing the lock and unlock buttons. If the doors unlock and lock according to your expectations, then you're good to go! You can now use the hands-free feature to lock and unlock your kia ceed key fob whenever your fingers become cold or you need to run errands around Brandon.

Note: Some key fobs might need to be programmed (transponder chips or smart keys). This requires a specific programming machine that only the dealer or locksmith can access. Other keys (non-transponder metal keys) do not require programming. If you're required to reprogramme your key, you'll have to write down the key code's number on the key code tag.

How do I replace a battery

If your Kia key fob is not responding to pressing the lock or unlock button on the fob, it is a sign that the battery should be replaced. A battery that is not functioning properly can cause other issues, such as the check engine light turning on or the engine not turning correctly. Fortunately replacing the key fob battery is a relatively easy DIY project that requires just some basic tools.

Before starting the process ensure that your vehicle is turned off and that all doors are closed. Find the small metal or plastic piece at the bottom of your key fob, and move it until a metal key pops out. You can then insert the key into the door handle of the driver to unlock your car.

To replace the key fob's battery, remove the cover on the rear and use a pry bar tool to remove the latch holding the black negative battery cable. Remove the old battery, and then align the new battery so that the "+" positive side faces you, while the "-" negative side is facing towards the fob's electronic contacts. Push the new CR2032 battery straight into position without putting too much force on it to avoid damaging or bending the contacts of the metal.

After you have installed the new battery, turn the key fob on and off in the ignition until the door locks cycle. Then, test your Kia key fob to see if it is working properly again.

How do you replace a smart keys

Depending on the model of your Kia sorento key fob Programming Sportage, you may have an ordinary key fob or a smart key. The difference between these is that the smart key kia key comes with tiny mechanical key blade in it, whereas the standard fob doesn't. Both key fobs are equipped with an internal battery that will eventually need to be changed. Fortunately, this is an easy process that only takes about two minutes.

Make sure you turn off your kia picanto key programming and be on a flat or well-lit surface prior to when you begin. Keep in mind that there are tiny pieces inside the fob that can fall out if you are not cautious.

The release button for the small size is located on the lower backside. It could be an oval silver button or a rectangular slot. When you press it mechanical key blade, it will appear and you can then open the key fob.

Once you have the key fob open then you can remove the old battery and replace it. The new battery is one called CR-2032 and can be bought online or in your local auto parts store. When you are done, you should be able to lock, unlock and start your vehicle with your key fob, even if your engine isn't running!

How do you replace the mechanical key

The Kia keyfob is an excellent convenience which allows us to lock or unlock our car by simply pressing one button. Like any other device like a key fob, the Kia can have issues at times. There are methods to fix these issues and keep our key fobs in good working condition for the long run.

A low or dead battery is one of the most frequently encountered issues. This can cause the fob to cease working or work intermittently. If this is the case it is time to replace the battery a new one.

If this doesn't fix the issue you can try using a standard flathead screwdriver and wedge it into the casing of the fob's plastic. Be careful not to damage any internal components, or scratch the plastic. After opening, carefully remove the old battery and replace it with a new one.

Close and open the door using the mechanical key. (Every 2011 kia soul key fob replacement fob comes with an emergency mechanical key which will fit into the slot). Test the key fob and ensure that it's working correctly. If the fob isn't functioning, contact an expert locksmith or dealer to resolve the problem. To avoid lockouts in the future, ensure you purchase an emergency key that will work on all trunk and door cylinders.